少妇厨房愉情理伦bd在线观_爽 好舒服 快 吸乳爽文软件_国产偷抇久久精品_欧美午夜福利精品一区_99爱精品视频在线播放_打扑克又痛又叫软件_国产尤物一区_黄色视频毛片视频_宅男在线观看亚洲av无码_亚洲欧美韩日综合

磁保持繼電器 DS908M 70A

下載資料Download

基本特性 Speciality:

線圈脈沖設置寬度Coil pulse width

50msec. Min

動作時間Operation time

20msec. Max

復歸時間Comeback time

20msec. Max

介質耐壓Dielectric strength

觸點與線圈間:

Between coil& contact

4000VAC


斷開觸點間:

Between contacts

1800VAC

絕緣電阻Insulation resistance

Min.1000M? (500VDC)

環境溫度 Ambient temp

-40℃~+70℃

重量 Weight

78g

引出端方式 Quick connect

PCB&QC

封裝形式  Plastic sealed dusted proof

塑封、防塵

外形尺寸不含輸出端子Size(mm)

Output terminal (mm) not included in profile size

54*30*18


觸點特性 Contact specification

觸點形式 Contact form

2A  2B

觸點材料Contact material

AgSnO2,

接觸電阻Contact resistance 

1.5mΩ Max.(12VDC 1A)

額定負載Contact current(Cosφ=1)

70A  250VAC

最大斷開電壓MAX disconnection voltage

440VAC / 110VDC

最大斷開功率MAX disconnection power

20000VA

額定負載電氣壽命(阻性)Electrical life

1×104cycles

機械壽命Mechanical life

1×105cycles


線圈參數Coil specification:        

額定電壓 

Rated Voltage (VDC)

                            電阻 Resisttance ±10%(Ω)

吸合/釋放電壓 Suction and 

Release Voltage (VDC)

單線圈Single
雙線圈Dual
6
16
8*2


≤70%額定電壓Rated Voltage

93618*2
125427*2
24256128*2

 

尺寸簡圖 及 安裝尺寸 Installation Sizemm 

4eebf20db8d5ca7440bd992ac34352d.png

接線圖 Connection Diagram 

10e54a62500e66dca9f829461c65217.png

注意事項 Application Notes

 

1. 所有繼電器在出廠時都設為閉合狀態。在裝運或組裝的過程中繼電器可能會變成釋放的狀態。因而使用時(電源接入時)請根據需要重新將其設置為復歸狀態。

2. 為了使繼電器保持在吸合或釋放的狀態,線圈電壓需達到額定電壓,為確保磁保持繼電器動作或復歸脈沖寬度小于50ms。不要向線圈上的Pin1和Pin2施加電壓超過一分鐘以上,以防線圈損壞。

3. 繼電器有極性區分,用戶需指明屬于何種極性。

4. 繼電器入廠檢驗及使用輕拿輕放,防止損壞影響參數,入廠做破壞性檢查的產品要與正常產品嚴格區分標識,不得裝機使用。

5. 非帶銅絞線的繼電器,負載引腳不能焊錫,引腳針剛性固定,不能隨意扭動。

 

1. All the relays are shipped in the "operate" position because it is possible that during transit or final assembly the relay could change its state to the "release" position. please reset the relay into "operate" state when put in circuit according to need.

2. In order to maintain "operate" or "release" state of the relay, the coil voltage should reach the rated voltage. The pulse width should be 60ms or longer to ensure a proper change of state. Do not enegize both Pin1 and Pin2 at the same time on the coil for longer than 1 min (damage to the coil).

3. Relays are classified according to the polarity, if client need different form from information, please contact us.

4. The relay into the factory for destructive inspection should be protected from damage and strict distinction between the normal products.

5. Now with braided line relay, the load pin can not solder, not arbitrarily wrenched, two pins and righid fixation.